Skip to content

How To Build a Miter Saw Stand

How one can construct a miter noticed stand with free plans and, footage and directions!

We frequently get requested what our favourite, most-used device is. I all the time reply the identical… It’s my miter noticed! It is likely one of the staple instruments in my workshop. I find it irresistible. I’ve had it on a stand for the final 12 months or so, and determined it was time to construct it a brand new residence. Try my DIY Miter Noticed Stand!

DIY Miter Saw Stand by Shanty2Chic

This can be a actually easy construct with the proper instruments! Let’s get began! I’ll stroll you thru the construct of the bench and the stand under.

You may construct this miter noticed station on any work floor you could have corresponding to a desk or a workbench. I constructed mine on a 2’ x 7’ cell workbench. I used the design of THIS workbench as my base, however made the size 7′ as an alternative of 8′. The free printable plans for each the workbench and miter noticed stand are on the backside of this publish.

Index

    Construct the Miter Noticed Stand Legs

    Step one is constructing 4 legs. These are produced from becoming a member of a 2×4 and a 2×6 piece collectively. I reduce every of those items at 27 ½” lengthy. I used my Kreg Pocket Gap Jig so as to add three 1 ½” pocket holes to 1 facet of every 2×4 piece. Then, I linked the two×4 to a 2×6 utilizing a line of wooden glue and a couple of ½” pocket gap screws.

    image

    Listed below are my 4 legs able to go!

    image 1

    Construct the workbench frames

    The subsequent step is constructing the frames of the workbench. There will likely be a high body and a backside body.

    Minimize Listing for Prime Body• 2 – 2×4 @ 84″ • 3 – 2×4 @ 20 ½”

    Recomendado:  Is San Francisco Safe? (Honest Advice, By a Local)

    Minimize Listing for Backside Body• 2 – 2×4 @ 78″ • 3 – 2×4 @ 14 ½”

    I added 1 ½” pocket holes to every of my 20 ½” items and every of my 14 ½” items. They need to look a bit like this, under.

    image 2

    I hooked up the shorter items to the longer items utilizing 2.5″ pocket gap screws and wooden glue. This created 2 “frames.”

    image 3

    For every body you should have one small piece on every finish and one within the center. Each frames will seem like this…

    image 4

    Connect legs to backside body

    The subsequent step is attaching the legs to the frames. I used the two ½” wooden screws by the again of the underside body and into every leg to carry all of it in place.  The underside of the body will likely be flush with the underside of the legs.

    image 5

    Connect backside plywood shelf

    After attaching the 4 legs to the underside body, you’re prepared in your plywood shelf. You should utilize the Kreg Rip-Minimize with a round noticed to make this step actually easy!

    Minimize Listing for Plywood Tops• Prime Piece – 24″ x 84″ • Backside Piece – 17 ½” x 78″

    After attaching the 4 legs to the underside body, I dropped within the first piece of plywood. I used 1 ¼” brad nails by the highest of the plywood and into the body to carry it in place.  You may also use MDF or different board for this half… Completely your choice!

    image 6

    Connect the highest body

    Now connect the highest body. I additionally used the two.5″ wooden screws on this half, however I went by the again of the legs and into the highest body. The highest of the body will likely be flush with the highest of the legs.

    Recomendado:  22 Indoor Water Parks Near Chicago for a Winter Escape Within Driving Distance
    image 7

    Connect the highest of the workbench

    The subsequent step for the workbench is including the plywood panel to the highest. I used brad nails by the highest piece of plywood and into the highest of the body. Straightforward peasy!  Once more, you need to use any materials in your workbench floor right here.

    Connect the casters

    Earlier than shifting on to the miter noticed station on high, I hooked up every of my casters to a chunk of two×6 reduce to five″. Then, I simply hooked up the wooden blocks with wooden screws by these items of wooden and into the legs of the desk. Bam. You now have a rolling workbench!

    image 8

    Construct the miter noticed station

    The miter noticed station I constructed is made particularly to suit my Ridgid Sliding Miter Noticed , however you possibly can simply modify it to suit yours! I began by constructing the fence first. I used a chunk of plywood ripped to 7.5″ huge, however you can even use a 1×8 reduce into two items for this. Mine have been 45″ and 14″. You could want to change these lengths to suit your noticed. I added ¾” pocket holes down one lengthy facet of those boards.

    image 9

    I lined each boards up with the fence of the noticed and hooked up it to the desk high utilizing 1 ¼” pocket gap screws and wooden glue.

    image 10

    You may see the way it traces up even with the fence of the miter noticed under.

    image 11

    Construct the shelf helps

    I measured the peak from the highest of the workbench to the reducing desk of the noticed. Mine was 4.625″. If you’re making this for a special noticed, that is the measurement that’s actually necessary! You need your reducing floor to be even with the helps you’re constructing to ensure you get straight cuts. I knew I used to be going to make use of ¾” scrap wooden for my wooden helps, so I subtracted that thickness, leaving me with 3 ⅞”. You should utilize any wooden materials in your helps. I used my desk noticed to tear a board of the plywood to this thickness. Then, I reduce that board into 12″ items. I added ¾” pocket holes to 1 facet and backside of every piece like this!

    Recomendado:  Quotations - Revolutionary War
    image 12

    Connect the scrap boards to the desk high utilizing 1.25″ pocket gap screws.

    image 13

    Every scrap board will even be hooked up to the again fence utilizing 1.25″ pocket gap screws and wooden glue.

    image 14

     

    image 15

    On the left facet of the noticed (the longer shelf), I spaced the scrap boards evenly aside, about each 12″. The 2 items to the proper of the noticed are 8″ aside.  This will even depart you some openings that present additional storage. I exploit plastic containers to retailer completely different screws, nails and different small instruments and {hardware}.

    image 16

    Connect the highest of the miter noticed stand

    The very last step is including the MDF board to the highest. The left facet MDF is reduce at 40″ from the longest level and the proper facet is reduce at 8″ from the longest level. I did select to chop the boards at a forty five˚ angle to permit area to rotate my noticed. I used brad nails to carry these high two items in place. Whew! All executed!

    image 17